4/10/2023 0 Comments Briqs data private limited![]() s a result attribute type IC comms set up for communication between controllers will operate successfully, and any preconfigured IQ will run its control strategy. ![]() If other IQs are present they will try to form a network together. ![]() It will try to form a network with any other Trend device on the trunk. The IQ can operate on the trunk without the /BINC being present. The /BINC has a default MC address of zero and a default BCnet network number equal to the Trend Lan number but both of these may be changed in the BINC s BCnet MSTP network module. IQ/VV IQ The BCnet MC address of an IQ will always be the same as its Trend device address. So that a 963 running on the PC would be able to interrogate both the IQs on Lan 9, and the on Lan 22 by way of vcnc1. USB IQ The two s vincs together create an internetwork. The other Ethernet is on a separate Lan (Lan22). BINC Ethernet The IQs are all on Lan 9 the Lan number has been set up in each IQ by the /BINC. In the above example they have addresses 11 to 13. If required they can be changed using IQTool. The IQs addresses are set in the factory on a rolling basis, (range 11 to 119). The scnc has been enabled by changing its address from zero to 6. In the equivalent logical diagram above, the BINC is shown with its default settings, Outstation 9 on Lan 9 vcnc1 is at address 1 (with port address 10001), and vcnc2 at 4 (with port address 10004). There cannot be another /BINC on the same trunk. Trend on The /BINC takes a Lan for itself, its vinc is always present and there cannot be another Ethernet on the same Lan as the BINC. This enables a supervisor, tool, or display panel to be connected by way of the RS232 port. scnc: The supervisor CNC is only present if the local supervisor port is set to a nonzero address. IQ/VV O13 vcnc1, vcnc2: There are two virtual CNCs, so that if a supervisor is connected to the /BINC, an engineering tool can also be conected by way of the other virtual CNC. The /BINC takes a Lan for itself so cannot join another Trend Lan on Ethernet. BINC Internetwork vinc vinc O9 BINC O126 O126 CNC scnc O6 CNC scnc O1 vcnc1 vcnc2 O4 Lan vcnc /MSTP/BINC control RS232 O11 CNC scnc vinc vcnc1 vcnc2 CNC scnc O125 O12 Lan 9 vinc: The /BINC always has a virtual INC (internetwork node contoller) unlike the basic which only has one if it is the lowest address on its Lan. any INC s address on its Lan), and the Lan number of the Lan is set in the /BINC (ddress module/local Lan). The address of the /BINC s vinc on this Lan is fixed at 126 (i.e. The IQs connect to, and together with the /BINC s internal nodes they form a local Lan. The /BINC s vinc connects to Ethernet on one side, and to on the other. SYSTEM Full system details of the are given in the Configuration Reference Manual TE200768 the /BINC details are given in the /MSTP/BINC/ supplement TE /BINC/ Controller The /BINC has an extra vcnc compared to the basic, so the internal nodes look like the diagram below: to a supervisor or tool using the /BINC s Ethernet connection or RS232 or USB serial port connections (although there is a remote chance of an address clash as described in the IQ Configuration Manual, TE ). This enables it to be used in a number of applications including the integration of IQs into the Trend system. (/BINC) acts as an interface between the Trend system and the trunk. BCnet over option board with terminator Physical Diagram shows XCT/12 the /00 version has zero I/O connectors earth (ground) input channels 263 mm (10.35 ) auxiliary board cover board 42 mm (1.65 ) 56 mm (2.2 ) 46 mm (1.81 ) Under cover input LEDs input links Under cover LEDs MSTP connector Terminator switch 150 mm (5.91 ) 130 mm (5.12 ) input power supply RS232 local supervisor connector, Ethernet LEDs P EN output channels supply to output power bus auxiliary output supply I/O Bus cover LEDs power watchdog I/O bus Under front panel output LEDs T Issue 5, 04Sep2013 1ΔΆ Functionality The./MSTP/BINC/. data sheet describes the additional functionality of the /MSTP/BINC/. Note that standard functionality is described in the data sheet T200505 this././mstp/binc/. The unit also contains standard functionality (e.g strategy), and provides virtual CNCs which allow supervisory or tool software running on PCs on the Ethernet network to connect to the Trend system. provides an interface between an trunk (and its IQ controllers) and the rest of the Trend Building Management System. 1 BCnet Internetwork Node Controller Description) Features The.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |